Carbon Steel Key Stock — Factory Direct Supplier | Huaxia-Steel
Carbon steel key stock, also known as machine key stock or square/flat key bar, is the raw material used to manufacture keys that transmit torque between a shaft and a hub. Huaxia-Steel supplies precision key stock in square and rectangular sections, cut to length or in standard bar lengths, in the grades and tolerances demanded by mechanical engineers and equipment manufacturers. All stock is mill-certified and supplied direct from the factory at competitive prices.
A mechanical key fits into a slot cut into both the shaft and the hub, preventing relative rotation and transmitting torque. The key stock must be accurate in cross-section and straight, because the fit determines how well the key seats and how much load it can carry. Our key stock is produced to tight dimensional tolerances and consistent mechanical properties so that it machines cleanly and performs reliably in service.
Product Overview
We offer key stock in the common square sizes from 3 mm to 50 mm and rectangular sizes to wider dimensions, in metric and inch series. Material is typically AISI 1018 or 1045 carbon steel — 1018 for general-purpose keys and 1045 where higher strength is needed. Bars can be supplied in standard mill lengths or precision cut to your specified length, with ends deburred and, if required, chamfered.
Key stock is widely used in motors, gearboxes, pumps, conveyors, and agricultural machinery. Because it is a stock item with many possible sizes, we keep a broad range in inventory and can also produce to non-standard dimensions for volume orders.

Specifications
| Parameter | Range / Detail |
|---|---|
| Square sections | 3×3 mm to 50×50 mm (1/8″ to 2″) |
| Rectangular sections | Width 4-100 mm, thickness 3-50 mm |
| Standard lengths | 1 m, 2 m, 3 m, 6 m, or cut to size |
| Materials | AISI 1018, 1045, or as specified |
| Tolerance | h9 / h11 on cross-section, or to DIN 6885 |
| Surface finish | Cold-drawn bright, or hot-rolled pickled |
| Straightness | Within standard commercial limits |
| Standard | DIN 6885, ISO 773, ANSI B17.1 |
Cross-sectional tolerance is critical for a proper key fit. Cold-drawn key stock provides a bright surface and tight tolerance suitable for most machine-key applications without additional machining. For large sections or special grades, hot-rolled and machined stock is available.
Available Grades and Materials
- AISI 1018: the most common key stock material, low-carbon, tough, easy to machine, and suitable for carburizing when a hard surface is required.
- AISI 1045: medium-carbon steel for higher-strength keys, can be quenched and tempered for demanding torque transmission.
- AISI 1020 / 1030: alternatives for general engineering where 1018 or 1045 is not essential.
- Low-alloy grades: available on request for special strength or wear requirements.
All key stock is traceable to its heat and supplied with a mill test certificate on request. We can also provide hardness and mechanical testing for critical applications.
Manufacturing Standards
Metric key stock and finished parallel keys are commonly produced to DIN 6885 and ISO 773, which define cross-sectional dimensions and tolerances for shaft and hub keyways. Imperial keys follow ANSI B17.1. Key stock itself is supplied as bar and is cut and machined by the customer into finished keys with the required end form (rounded, square, or tapered).
Our cold-drawing process reduces the section to precise dimensions while improving surface finish and strength through work hardening. For 1045 and other medium-carbon grades, the stock can be supplied normalized or annealed to optimize machinability, then heat treated by the customer after the key is machined.

Applications
- Machine keys for electric motors, gearboxes, and reducers.
- Pump and compressor shafts and impellers.
- Conveyor drive and idler rollers.
- Agricultural machinery and power transmission equipment.
- Fan and blower hubs.
- General shaft-hub connections in industrial equipment.
Quality Assurance
We inspect key stock for cross-sectional dimensions, straightness, and surface condition. Samples from each lot are measured with calipers or micrometers at multiple points to confirm tolerance, and the surface is checked for seams, scratches, and scale. Material chemistry is verified against the mill certificate, and hardness testing is available where specified.
For customers who machine finished keys from our stock, we can supply first-article inspection data and dimensional reports to support your incoming quality control. Third-party inspection can be arranged for large or critical orders.
Packaging and Shipping
Key stock is bundled in straight lengths, strapped securely, and protected against bending and moisture during transit. Cut-to-length pieces are packed in cartons or crates with clear size and grade labels. Bundles are palletized for container loading, and we can combine key stock with bar and flat products to consolidate freight. Export marking and documentation are handled to your specification.
Frequently Asked Questions
What is the difference between key stock and a finished key?
Key stock is the raw bar material sold in lengths; a finished key is cut and machined from that stock to a specific length and end form to fit a shaft and hub.
Should I choose 1018 or 1045 key stock?
Choose 1018 for general-purpose keys that may be carburized for a hard case, and 1045 when you need higher core strength and can heat treat the finished key.
Can you cut key stock to my required length?
Yes. We offer cut-to-length service with deburred ends, and can chamfer ends to drawing for volume orders.
What tolerance does your key stock hold?
Cold-drawn key stock is typically supplied to h9 or h11 on the cross-section, and we can produce to DIN 6885 tolerances on request.
Do you supply imperial inch sizes?
Yes. We stock both metric square/rectangular sections and imperial inch sizes, and can produce to ANSI B17.1 dimensions.
Key Types and Standards Overview
Mechanical keys come in several forms, and key stock is the starting material for each. Understanding the distinction helps you order the right section and material for the key you will manufacture.
| Key type | Description | Typical use |
|---|---|---|
| Parallel key (square/rectangular) | Uniform cross-section, straight sides | The most common key for shafts and hubs |
| Taper key | Slight taper on top surface | Applications needing a wedging fit |
| Woodruff key | Semicircular disc | Tapered shaft ends, automotive |
| Feather key | Allows axial sliding | Sliding gears and clutches |
| Gib-head key | Headed for easy removal | Shafts where disassembly is frequent |
DIN 6885 and ISO 773 define parallel keys and their shaft/hub keyways in metric sizes, while ANSI B17.1 covers inch-series keys. When you buy key stock, you are buying the bar from which parallel or taper keys are cut and finished. Square sections suit smaller shafts, and rectangular sections are used where greater width improves torque capacity.
Machining and Installation Tips
Cut key stock to the required length with a saw or abrasive wheel, then deburr and chamfer the ends. The key should fit the keyway with a light side fit — snug enough to transmit torque without play, but not so tight that it must be hammered in. A key that is too loose will fret and wear; one that is too tight can distort the hub or crack the keyway.
For high-torque or impact applications, consider carburizing a 1018 key to develop a hard wear-resistant case over a tough core, or quench and temper a 1045 key for through hardness. Always verify the finished key against the shaft and hub keyway dimensions before assembly, and replace a key that has been deformed — a worn key should never be reused in a critical drive.
Ordering Information Checklist
- Section shape and size (square or rectangular, with width and thickness).
- Material grade (AISI 1018, 1045, or as specified) and delivery condition.
- Bar length or cut-to-length requirement, with end treatment.
- Dimensional tolerance (h9, h11, or DIN 6885) and straightness.
- Surface finish: cold-drawn bright or hot-rolled pickled.
- Quantity and any mill certificate or inspection requirements.
Send us your key schedule and we can consolidate multiple section sizes into one order, reducing freight and simplifying incoming inspection. For volume customers we hold common sizes in stock for rapid dispatch.
Why Buyers Choose Huaxia-Steel
Our key stock is drawn or rolled to tight cross-sectional tolerances, with straightness and surface condition checked on every lot. We stock the common metric and inch sections, offer cut-to-length service, and can supply material certificates and inspection reports. Consolidating multiple section sizes into one order is straightforward, and our export packing protects the bar from bending and corrosion in transit.
Every order is backed by responsive communication and a clear documentation package. Our sales team can help you confirm specifications, select the right grade or finish, and plan delivery to match your production schedule. For repeat customers we hold stock against blanket orders and offer priority scheduling. Contact us with your requirement and experience the advantage of buying factory direct.
Request a Quote
Need carbon steel key stock in metric or inch sizes? Huaxia-Steel supplies 1018 and 1045 square and rectangular key stock, cut to length or in mill lengths, with mill certificates. Send us your section, grade, and quantity for a factory-direct quote.
Contact our sales team at [email protected] with your specification, quantity, and destination port. We reply with a mill-direct quotation, lead time, and full documentation within one business day.





