ASTM A515 Carbon Steel Plate — Factory Direct Supplier | Huaxia-Steel
ASTM A515 is a carbon steel plate specification for pressure vessels and boilers operating at intermediate to high temperatures. Huaxia-Steel stocks ASTM A515 Grade 60, 65, and 70 plates, normalized, with thicknesses from 6 mm to 100 mm, and supplies them with EN 10204 3.1 mill certificates. This page covers grades, chemistry, mechanical properties, and procurement guidance.
Product Overview
A515 plates are killed carbon steels intended for fusion-welded pressure vessels where improved toughness is not the primary requirement. Grade 70 is the most widely used for boiler drums and pressure shells. All grades are supplied normalized to ensure uniform grain structure and predictable forming behavior.

Specification Table
| Parameter | Range / Value |
|---|---|
| Grades | A515 Grade 60 / 65 / 70 |
| Thickness | 6 mm to 100 mm |
| Width x length | Up to 3000 x 12000 mm |
| Condition | Normalized |
| Standards | ASTM A515 / A515M; ASME SA-515 |
| Certificate | EN 10204 3.1 |
| Edges | Mill, sheared, or plasma-cut |
Available Grades
Grade 60 (minimum tensile 415 MPa), Grade 65 (450 MPa), and Grade 70 (485 MPa) differ mainly in strength. Grade 70 is preferred where higher allowable stress reduces wall thickness and weight. Select the grade that matches your design code allowable stress to avoid over-specifying.
Manufacturing Standards
Plates are produced to ASTM A515 / A515M and the equivalent ASME SA-515 pressure-equipment specification. We supply normalized plates with ultrasonic testing per SA-578 on request, and can provide third-party inspection and impact testing when the project requires it.

Chemical and Mechanical Properties
Typical limits and properties are summarized below; exact values come from the mill certificate for each heat.
| Grade | C max (t<=25mm) | Tensile MPa | Yield MPa |
|---|---|---|---|
| Grade 60 | 0.24 | 415-555 | 220 |
| Grade 65 | 0.28 | 450-585 | 240 |
| Grade 70 | 0.31 | 485-620 | 260 |
Applications
A515 plates are used for boiler drums, pressure vessels, heat exchangers, and refinery equipment operating at elevated temperature. They are also found in storage tanks and reactor shells where moderate-temperature strength and good weldability are required.
Quality Assurance
Each plate carries a traceable heat number and is supplied with an EN 10204 3.1 certificate showing chemistry, tensile, and bend results. Optional ultrasonic testing, hardness mapping, and third-party inspection (SGS, BV, TUV) are available to match project specifications.
Packaging and Shipping
Plates are stacked with separators, edge-protected, and bundled with steel strapping, then shipped via flat-rack or in containers with moisture barrier. We handle export packing, marking per client ISO, and combine with other plate and structural orders to optimize freight.
Manufacturing Process
A515 plates are produced by continuous casting, rolling, and normalizing. Normalizing (reheating above the transformation temperature and air cooling) refines the grain and gives uniform properties through the thickness, which matters for pressurized components. Plates are then inspected, marked with the heat number, and prepared for shipment.
Dimensional Tolerances
Thickness, flatness, and width follow ASTM A20 (the governing specification for steel plates for pressure equipment) and the ordered thickness basis. We can supply mill-edge or trimmed-edge plates and cut to length or shape per drawing. Ultrasonic testing per SA-578 is available for critical thicknesses.
How to Choose the Grade
Pick the lowest grade that meets your design allowable stress to minimize cost and weight. Grade 70 is common for new vessels; Grade 60 or 65 may suffice for lower-pressure or lower-temperature margins. Confirm against the applicable ASME or EN design code before ordering.
Weldability and Fabrication
A515 is readily weldable with preheat for thicker sections to avoid hydrogen cracking. Follow a qualified WPS and post-weld heat treatment where the code requires it. Its normalized condition gives predictable heat-affected-zone properties, which simplifies fabrication planning.
Storage and Handling
Plates should be stacked on level supports with separators to prevent warpage and allow air circulation. Protect cut edges from moisture, and keep mill certificates with the material for traceability through fabrication and inspection.
ASTM A515 vs A516
A515 and A516 are both carbon steel pressure-vessel plates, but A516 (including the normalized Grade 70) is the preferred choice for low-temperature and impact-toughness service, while A515 is intended for intermediate to higher temperature where impact toughness is secondary. Many modern designs specify A516 Grade 70; choose A515 when the code and service temperature align with its scope.
International Equivalents
A515 is broadly equivalent to GB/T 713 Q345R / Q370R (China) and close to EN 10028-2 P275/355 grades (Europe) for pressure equipment, though chemistry and test details differ. We can advise on acceptable substitutions and supply the required certificates for cross-standard projects.
Project Supply and Cutting
We cut A515 plates to size or shape (CNC plasma, laser, or oxy-fuel), bevel edges for welding, and deliver nested to minimize offcut. For EPC projects we manage multi-size plate packages with unified marking and documentation, supporting direct-to-site delivery.
Selecting Plate Thickness
Plate thickness is driven by the design code allowable stress and the required corrosion allowance. Choose the thinnest section that satisfies both to save weight and welding cost, but never below the code minimum. For vessels with a long service life in corrosive duty, add a corrosion allowance of 1.5 to 3 mm to the calculated thickness before selecting the nominal plate.
Remember that thicker plates cool more slowly and may need adjusted welding procedures; discuss very thick orders with your fabricator so the material and the WPS are compatible. We can supply ultrasonic-tested thick plates for critical zones where laminar defects must be excluded.
A515 in ASME Code Applications
Under the ASME Boiler and Pressure Vessel Code, A515 (SA-515) is permitted for pressure vessels, with Grade 70 the most common. Designers should verify the applicable temperature limits and impact requirements, since A515 is intended for intermediate to higher temperature service where low-temperature toughness is not the controlling factor. Where toughness is required, A516 Grade 70 is usually specified instead.
Why Buy Factory Direct
Buying A515 plate direct from a stockholding manufacturer gives you normalized material with traceable mill certificates, cut-to-size service, and competitive pricing without distributor markup. For EPC projects we manage multi-thickness plate packages with unified marking and documentation, and deliver nested to minimize offcut. Direct supply also shortens lead time for non-stock thicknesses.
Plate Marking and Traceability
Every A515 plate carries the heat number, grade, thickness, and standard near one corner, and we supply a matching mill certificate so the material can be traced through fabrication and into the finished vessel. For coded vessels, maintain this link so an inspector can confirm any plate’s chemistry and properties on demand. Lost markings should be re-verified, not guessed.
Choosing the Cutting Method
Plasma cutting is fast and economical for most thicknesses up to about 40 mm; laser gives cleaner edges on thinner plate; oxy-fuel suits very thick sections. Beveling can be done in the same setup for weld preparation. Tell us the edge quality and bevel you need so we cut once correctly and avoid rework at the fab shop.
Grade Comparison Table
| Grade | Tensile MPa | Typical use |
|---|---|---|
| Grade 60 | 415-555 | Lower-pressure vessels |
| Grade 65 | 450-585 | Mid-range vessels |
| Grade 70 | 485-620 | Boilers, high-pressure shells |
Choose the lowest grade meeting your allowable stress; Grade 70 is the common default for new boilers. Confirm the selected grade against the design code before ordering.
Mill Test and Third-Party Options
Every plate ships with an EN 10204 3.1 certificate as standard; 3.2 with independent endorsement is available for coded vessels. We arrange SGS, BV, or TUV witness of ultrasonic testing and mechanical tests on request, and provide the full inspection record for your project quality file.
Planning a Plate Procurement Program
For owners and EPCs that consume A515 plate regularly, a procurement program beats one-off orders. Forecast your thickness mix, agree stocking levels with the supplier, and use call-off orders to draw material against a frame agreement. This smooths price volatility, shortens lead times, and gives you priority during tight market conditions. A good program also standardizes thicknesses and grades across projects, which reduces offcut and simplifies fabrication setups.
Within the program, decide whether to buy mill-edge or trimmed-edge plate, and whether to take material already cut to size or as full plates for the fabricator to cut. Cut-to-size reduces handling and scrap at the fab shop but requires accurate demand; full plates offer flexibility but more on-site processing. We can support either model, including nested cutting to your drawings so you pay close to net weight. Matching the supply model to your workflow is a worthwhile planning exercise.
Finally, build quality requirements into the frame agreement: certificate type, UT level, and any third-party inspection, so every release meets the same bar without renegotiation. A clear, pre-agreed specification lets expeditors release material quickly and keeps the whole program auditable, which is exactly what lenders, insurers, and operators expect on coded pressure-equipment projects.
Common Questions From Buyers
Buyers often ask whether A515 Grade 70 can substitute A516 Grade 70. The short answer is only when the design does not require the low-temperature toughness that A516 provides; for most new pressure vessels A516 Grade 70 is preferred, so confirm with your code and design engineer before substituting. Another frequent question is about maximum thickness; A515 is produced well beyond 100 mm, but very thick plates need careful welding procedure qualification. We are happy to advise on these points using your specific design conditions rather than giving a generic answer that might not fit your case.
Request a Quote
Buy ASTM A515 Grade 60/65/70 plates cut to size with mill certificates. Huaxia-Steel offers normalized stock and fast global delivery.
Contact our sales team at [email protected] with your specification, quantity, and destination port. We reply with a mill-direct quotation, lead time, and full documentation within one business day.





