Search
Close this search box.

Carbon Steel Flange Nut — Factory Direct Supplier | Huaxia-Steel

A carbon steel flange nut is a hexagonal nut with a wide, integral circular flange at its base. The flange spreads the clamping load over a larger bearing surface, removing the need for a separate washer in many assemblies and reducing the risk of damage to softer mating materials. Flange nuts are used in automotive, machinery, construction equipment, and general industrial fastening wherever vibration resistance and fast assembly are important. This page covers our factory-direct range of carbon steel flange nuts, including dimensions, strength classes, manufacturing standards, coatings, and selection guidance.

We supply flange nuts in metric sizes from M5 to M36 and imperial sizes from 1/4 inch to 1-1/2 inch, in low and medium carbon steel with zinc, hot-dip galvanised, phosphate, or plain finishes. Serrated and non-serrated flange designs are available, with strength classes ranging from 4 through 10 and SAE grades 2, 5, and 8.

Product Overview

The defining feature of a flange nut is the circular collar formed integrally at the bearing face. On a standard hex nut, the clamping force is concentrated under the six corners, which can embed into the joint surface or crush a thin sheet metal panel. The flange distributes that load over roughly twice the area. In a serrated version, radial teeth on the flange bite into the mating surface to resist loosening from vibration — a useful feature, though one that limits reuse and can damage coated surfaces.

Flange nuts are produced by cold forming rather than machining. A slug of wire is pressed through a series of dies that form the hex body and flange in one operation, after which the thread is tapped or formed and the part is heat treated if required. Cold forming preserves the fibre flow in the steel and is highly economical at volume, which is why flange nuts are typically cheaper than a hex nut plus a separate hardened washer.

carbon steel flange nut application

Metric Dimensions and Weight

ThreadAcross flatsFlange diameterHeight (incl. flange)Approx. weight
M58.0 mm10.0 mm5.0 mm0.9 g
M610.0 mm12.5 mm6.0 mm1.8 g
M813.0 mm16.0 mm8.0 mm3.6 g
M1015.0 mm19.0 mm10.0 mm6.0 g
M1218.0 mm23.0 mm12.0 mm10.5 g
M1624.0 mm30.0 mm16.0 mm24.0 g
M2030.0 mm37.0 mm20.0 mm46.0 g
M2436.0 mm44.0 mm24.0 mm78.0 g
M3046.0 mm56.0 mm30.0 mm150.0 g
M3655.0 mm66.0 mm36.0 mm250.0 g

Dimension values reflect the common DIN 6923 / ISO 4161 pattern. Across-flats, flange diameter, and total height are inspected on every production setup. Imperial flange nuts follow a similar geometry with across-flats dimensions matched to the relevant bolt size. Custom dimensions can be produced against a drawing for OEM applications.

Dimensional Tolerances and Thread Fit

Thread fit deserves particular attention on plated flange nuts. A zinc layer adds thickness to the internal thread, so a nut tapped to 6H before plating may become tight on a 6g bolt afterwards. For hot-dip galvanised assemblies we normally tap to 7H, or we specify that the mating bolt thread is also galvanised and gauge the pair together.

Available Grades and Materials

Grade / classMaterialMin proof stressTypical application
Class 4Low carbon steel340 MPaLight assembly, furniture, non-critical fixtures
Class 6Medium carbon steel480 MPaGeneral machinery and equipment
Class 8Medium carbon, quenched and tempered600 MPaAutomotive, high-vibration machinery
Class 10Alloy or refined carbon steel830 MPaHigh-strength structural and equipment joints
SAE Grade 2Low carbon steelDominant in imperial general useGeneral purpose
SAE Grades 5 / 8Medium carbon / alloyHigher proof loadsAutomotive and heavy equipment

Most general industrial orders specify Class 8 metric or SAE Grade 5 imperial, which offers a good balance of strength, ductility, and cost. Class 10 or Grade 8 is reserved for joints where the bolt itself is high strength and the nut must develop the full tensile capacity of the fastener without thread stripping.

carbon steel flange nut stock

Manufacturing Standards

Metric flange nuts are made to DIN 6923 and ISO 4161, with thread form to ISO 965 and mechanical properties to ISO 898-2. Imperial flange nuts follow ASME B18.2.2 with mechanical classes defined by SAE J995. Zinc coatings are applied to ASTM A194 / ASTM B633 as appropriate, and hot-dip galvanising to ASTM A153 or ISO 10684. We can also produce to customer drawings for automotive or OEM specifications.

Production flow is tightly controlled: wire rod incoming inspection, cold heading, thread forming or tapping, heat treatment where the grade requires it, coating, and final inspection. Hardness is checked on a sampled basis after heat treatment, and thread gauges are verified at the start of each shift. Certificates of conformance with mechanical test results accompany every shipment.

Serrated vs Plain Flange

A plain flange nut provides the bearing-area benefit without attacking the joint surface. It is the right choice when the mating surface is painted, coated, stainless, or otherwise needs to remain undamaged, and when the nut may be removed and reused. A serrated flange nut adds a locking function: the teeth embed into the surface and create friction that resists rotation under vibration.

Serrated nuts are widely used in automotive and equipment assembly, but they have limitations. They are generally intended for one-time use, they should not be fitted against soft materials or thin coatings, and they require a harder mating surface to bite into effectively. If vibration resistance is needed on a coated assembly, consider a nylon-insert nut or a wedge-locking washer instead.

Applications

Flange nuts appear in automotive chassis and engine assemblies, agricultural machinery, construction equipment, gearboxes, conveyors, steel framing, solar mounting systems, and electrical enclosures. They are particularly useful where the mating surface is thin sheet metal: the flange prevents the nut from pulling through the hole or distorting the panel during tightening.

In outdoor and marine environments, specify hot-dip galvanised or a corrosion-resistant coating and account for the thread allowance. For assemblies exposed to strong vibration, a serrated flange or a locking variant is preferable to a plain nut with a separate spring washer, which is often less effective than buyers assume.

Quality Assurance

Incoming wire rod is checked against the ordered grade and heat number. During production we monitor die wear, because a worn forming die produces an out-of-round flange that reduces bearing contact. Hardness testing confirms the heat-treatment result for Classes 8 and 10, and proof-load testing is performed on a defined sample from each lot.

Finished nuts are inspected for thread gauge conformity, across-flats dimension, flange flatness, coating coverage, and surface defects such as cracks or laps. Coating thickness is measured with a magnetic gauge on a sample from each barrel. Inspection records and certificates are retained against the lot number so any shipment can be traced back to its production batch.

Packaging and Shipment

Flange nuts are packed in export-grade cartons of 100 to 1,000 pieces depending on size, with a printed label showing thread size, class, finish, and lot number. Cartons are palletised and stretch-wrapped for sea freight, and desiccant is added for galvanised goods travelling through humid climates. Mixed containers with bolts, washers, and other fasteners can be arranged.

Standard export documents include the commercial invoice, packing list, certificate of conformance, and mill certificate where requested, so your receiving team has the full traceability record. Stock sizes normally ship within 7 to 15 days. Special heat treatments, non-standard coatings, or custom dimensions require confirmation of tooling and lead time before order placement.

Frequently Asked Questions

Do flange nuts replace washers?

In many applications yes. The integral flange spreads the load over a wider area, so a separate flat washer is often unnecessary. A hardened washer is still recommended on soft or coated surfaces.

Can serrated flange nuts be reused?

Generally no. The teeth deform on first tightening and lose their locking effect. For reusable assemblies, choose a plain flange nut with a locking washer or a nylon-insert nut.

Which class should I order for general machinery?

Class 8 metric or SAE Grade 5 imperial suits most general industrial joints. Move to Class 10 or Grade 8 only when the bolt is high strength and full tensile development is required.

Why do galvanised nuts need a larger thread tolerance?

Zinc coating adds thickness to the internal thread. Tapping to 7H provides the clearance needed for the nut to fit its plated bolt after coating.

Do you offer custom flange dimensions?

Yes. We can produce flange nuts to a customer drawing for OEM applications, subject to tooling confirmation and minimum quantity.

Request a Quote

We manufacture carbon steel flange nuts in metric and imperial sizes, plain or serrated, with a choice of strength classes and corrosion-resistant finishes. Send your thread size, class, quantity, and destination port for a factory-direct quotation and lead time.

Contact our sales team at [email protected] with your grade, dimensions, quantity, and destination port. We reply with a mill-direct quotation, lead time, and full documentation within one business day.

Request A Free Quote

 Or contact us to see our certificates

We’d like to work with you

If you require further information about our metal sheet products or architectural projects, please don’t hesitate to leave your contact details and message here.

Our team of experts will respond within 24 hours to continue the discussion and provide you with any additional information you requires.