Search
Close this search box.

Carbon Steel Set Screw — Factory Direct Supplier | Huaxia-Steel

Carbon steel set screws, also called grub screws or socket set screws, are headless fasteners used to secure a component against rotation or axial movement on a shaft. Huaxia-Steel manufactures set screws in metric and inch sizes, with cup, cone, flat, and dog points, in a range of strength classes and finishes. Supplied factory-direct with full traceability, our set screws deliver reliable clamping performance at a competitive price for machinery, tooling, and equipment assembly.

Unlike a bolt, a set screw has no head and is driven entirely from within its threaded body, usually by a hex socket or a slotted drive. It is threaded into a tapped hole in one part and its point presses against another part — typically a shaft — to lock the assembly. Choosing the correct point style, length, and strength class is essential for a secure, damage-free joint.

Product Overview

We supply hex socket set screws to DIN 913, DIN 914, DIN 915, DIN 916, and ISO 4026-4029 standards, and slotted set screws to DIN 551/552/553. Metric sizes range from M1.6 to M24 and imperial sizes from #0 to 1 inch. Standard point styles include cup point (the general-purpose choice), cone point (for hardened shafts and precise location), flat point (for a broad, non-marring contact face), and dog point (for pre-drilled locating holes).

Strength classes range from 14H (low) through 22H and 33H (high), with corresponding minimum hardness values. Zinc plating is the standard finish, with black oxide, phosphate, and hot-dip galvanizing available for different corrosion environments.

carbon steel set screw application

Specifications

ParameterRange / Detail
Metric sizesM1.6 to M24 (coarse and fine thread)
Imperial sizes#0 to 1 inch
Drive typesHex socket (Allen), slotted, Torx on request
Point stylesCup, cone, flat, dog, half-dog
Strength classes14H, 22H, 33H (DIN/ISO); 2A-5A (inch)
MaterialsAISI 1018 / 1045 / 4140 carbon and alloy steel
FinishesZinc plated, black oxide, phosphate, HDG
StandardsDIN 913-916, ISO 4026-4029, ANSI B18.3

Length is measured from the bottom of the headless body to the tip. Selecting the correct length ensures the point engages the shaft securely without bottoming out or protruding. We can advise on length selection for your specific assembly.

Available Grades and Materials

All set screws are produced from certified wire or bar stock, and hardness and mechanical test reports can be provided. Heat treatment is controlled to achieve the specified class, and each lot is sampled for compliance.

Manufacturing Standards

Metric hex socket set screws follow ISO 4026 (flat point), 4027 (cone point), 4028 (dog point), and 4029 (cup point), with equivalent DIN 913-916 numbers. Imperial socket set screws follow ANSI B18.3. Slotted set screws are covered by DIN 551 (flat point), 552 (cone point), and 553 (cup point). Threads are rolled or cut to class 6g (metric) or 2A (inch).

Manufacture involves cold heading the blank, forming the socket or slot, rolling the threads, and machining the point. Heat treatment develops the required hardness, after which the finish is applied. Cup points are the most widely used because they provide good holding power with a slightly concave edge that bites into the shaft.

carbon steel set screw stock

Applications

Quality Assurance

We inspect set screws for dimensional accuracy, thread fit, socket integrity, point geometry, and hardness. Thread gauging confirms the class, and hardness testing verifies the strength class on samples from each lot. Coating thickness and appearance are checked, and salt-spray testing is available for corrosion-critical orders.

Mill test certificates and hardness reports accompany material lots. For first orders or critical applications, third-party inspection (SGS, BV, TUV) can be arranged, and we maintain heat-number traceability through production.

Packaging and Shipping

Set screws are packed in sealed plastic bags inside labelled cartons, commonly 25 kg per carton, with quantity and size clearly marked. Small precision sizes can be packed in compartmented boxes. Cartons are palletized and stretch-wrapped for container transport, with moisture protection for plated goods. We handle export documentation and can consolidate set screws with other fastener items in one shipment.

Frequently Asked Questions

Which point style should I choose?

Cup point is the general-purpose choice with strong holding power. Use cone point for a firm grip on hardened shafts, flat point when you want a broad non-marring contact face, and dog point for positive location in a drilled hole.

What does strength class 33H mean?

Class 33H indicates a minimum Vickers hardness level for alloy steel set screws, corresponding to high strength and resistance to deformation under repeated tightening.

Can set screws damage the shaft?

Cup and cone points can mar softer shafts. Use a flat point or place a soft washer between the point and the shaft when surface preservation matters.

Do you supply fine thread set screws?

Yes. Both coarse and fine threads are available in metric sizes, and we can produce to ANSI B18.3 imperial requirements.

What finish is best for corrosion resistance?

Zinc plating suits general indoor use. For outdoor or marine environments, hot-dip galvanizing or a phosphate plus oil finish provides better protection.

Point Style Selection Guide

The point of a set screw determines how it grips the shaft and what damage it may cause. Choosing the right point is as important as choosing the right size.

Point styleGrip characteristicRecommended use
Cup pointSharp annular edge bites into shaftGeneral purpose, hardened or soft shafts
Cone pointConcentrated, deep penetrationHardened shafts, precise axial location
Flat pointBroad flat contact, minimal marringSoft shafts, frequent adjustment
Dog pointFlat nose fits a drilled holePositive location, repeated assembly
Half-dog pointReduced nose, moderate gripCompromise between cup and dog

Cup point is the default for most applications because it combines strong holding power with simple geometry. Cone point provides the strongest grip on hardened steel but leaves a small indentation. Flat point spreads the load and is the kindest to the shaft surface. Dog point requires a matching drilled hole in the shaft but gives excellent repeatability when a part is assembled and disassembled often.

Torque, Clamping, and Thread Locking

A set screw is tightened to a torque appropriate for its size and strength class. Over-tightening can strip the tapped thread in the hub or deform the screw socket, while under-tightening allows the joint to slip. Use a correctly sized hex key and, for critical assemblies, follow the torque recommended for the screw class.

Vibration is the main enemy of set screws. Where joints are subject to vibration, use a higher strength class, a cup or cone point that bites securely, and a thread-locking compound where disassembly is not frequently required. For the most demanding service, consider an alternative locking method such as a key, a collar, or a prevailing-torque device — a set screw alone is not always sufficient.

Ordering Information Checklist

With a broad stock of sizes and the ability to produce to drawing, Huaxia-Steel can supply set screws for everything from small instrumentation to heavy machinery. Send your specification and quantity for a prompt factory-direct quotation.

Why Buyers Choose Huaxia-Steel

Our set screws are manufactured from certified steel, heat treated to the specified class, and checked for thread fit, point geometry, and hardness. We stock a broad range of sizes, point styles, and finishes, and can produce to drawing for special requirements. Whether you need a small instrumentation screw or a high-strength screw for heavy machinery, we can supply it with full documentation and reliable delivery.

Every order is backed by responsive communication and a clear documentation package. Our sales team can help you confirm specifications, select the right grade or finish, and plan delivery to match your production schedule. For repeat customers we hold stock against blanket orders and offer priority scheduling. Contact us with your requirement and experience the advantage of buying factory direct.

Request a Quote

Need carbon steel set screws in bulk? Huaxia-Steel supplies hex socket and slotted set screws in metric and inch sizes, all point styles and strength classes, with mill certificates and fast global delivery. Send us your specification for a factory-direct quote.

Contact our sales team at [email protected] with your specification, quantity, and destination port. We reply with a mill-direct quotation, lead time, and full documentation within one business day.

Request A Free Quote

 Or contact us to see our certificates

We’d like to work with you

If you require further information about our metal sheet products or architectural projects, please don’t hesitate to leave your contact details and message here.

Our team of experts will respond within 24 hours to continue the discussion and provide you with any additional information you requires.